Paradox
©
Fisana

Jump to content


Photo
* * * * * 1 votes

How Ziran gets down on mini monos


  • Please log in to reply
3 replies to this topic

#1 Ziran

Ziran

    Mycophiliac

  • Free Member
  • 18 posts

Posted 05 April 2021 - 05:07 AM

How Ziran gets down on mini mono's

I like myself a mini mono. Love the fact that if it trichs out, I don't loose nearly as much spawn. Its a similar principle as my mini trays I do. If you haven't checked those out, you can find them at this link here ---> Link to Trays

I've made a few different style tubs from the 1719 style latch tub. There are a few designs and most will work if you dial your poly or micropore tape properly. I also use the 31 quart homz tubs.

 

1
2


I measure where I want my holes. I want them about an inch above the surface of the substrate. So, I like my holes to be about 4 inches to about 5 inches above the sub. Depending on my substrate height.

 

3
4


In total, you will have 4 holes. 2 top ones by the latches, and 2 in the middle of the bottom of the long sides of the tote.

Now for this design, I'm using a 1 and 1/4 inch hole saw for all my hole. You will want two on the long sides, and two at the top at the top of the short sides, just below the latches. Once they are cut, Micropore tape em up, or polyfil em.

 

5


I like to introduce fruiting conditions right away, so load her up with your spawn and substrate, then mix well, and introduce fruiting conditions.

 

6


Pinning

 

7

 

8

 

9


Almost ready.

 

10


Harvest day, and 8 hours later
 

11
12
14
15


Same design for the 31 quart tubs as well.

 

16


Pins!

 

17

 

18


Short guys, but fatties.

 

19

 

20


Harvest

 

21


Another Run of the same 31 quart tub, except with a much deeper substrate.

 

24

 

25


There are a few other designs I've done.

Two holes on each long side, about 1 inch holes and then 5 - 1/4" inch holes at the top.

1st Flush - First Harvest

 

26
27

2nd Harvest - First Flush

 

28

30


Same design, Spawned to Hpoo
 

32
33
34
35


Another Design was 3 1/2" Holes Across the bottom and 3 1/4" Holes across both sides on the top
 

36
37
38


Another 31 Quart Mono - I did a much deeper sub than I normally would. 2 quarts of spawn.
 

42
43
44
45
46
47
48
49
50
51
52
53
54
55.jpg
56.jpg

Another Tub - 2 4 oz pfcakes and 2 1/2 Pint cakes to coir.

 

60.jpg
61.jpg
62.jpg
63.jpg

 


  • Sidestreet, PJammer24, SteampunkScientist and 1 other like this

#2 BlueSkyCloud

BlueSkyCloud

    Mycophiliac

  • Free Member
  • 26 posts

Posted 08 April 2021 - 06:41 AM

Cool stuff. In your opinion what prevented those tubs from going full canopy?


Edited by BlueSkyCloud, 08 April 2021 - 06:41 AM.


#3 PJammer24

PJammer24

    Archetype Novice

  • OG VIP
  • 2,599 posts

Awards Bar:

Posted 08 April 2021 - 09:00 AM

Cool stuff. In your opinion what prevented those tubs from going full canopy?

 

likely genetics



#4 Ziran

Ziran

    Mycophiliac

  • Free Member
  • 18 posts

Posted 08 April 2021 - 11:58 PM

Cool stuff. In your opinion what prevented those tubs from going full canopy?

 

 

 

Cool stuff. In your opinion what prevented those tubs from going full canopy?

 

likely genetics

 

Combo of this, and some of those were my earlier designs, so that couldn't of helped.

 

Also, to much FAE can really dry out the edges. I might of needed to tighten up the MP tape on some of those runs. but that all comes with practice.


Edited by Ziran, 08 April 2021 - 11:59 PM.





Like Mycotopia? Become a member today!